My Jeep Compass Forum banner

General Information

Rubicon TJ
Stock Rubicon Package
Purchased New 02/07
2006 Jeep Rubicon TJ (Black)


AEM Air Filter w/Heat Wrap
Relocated Air Temp Sensor
4.6 L V8 Mustang Injectors
Magnaflow Cat Back exhaust
Six Speed Manual
Stock Rubicon Dana 44 w/the Lockers
241OR Transfer Case
On Board Air by Viair
Yellow Top Battery w/Winch Master Switch to the winch
A/C, P/B, P/S, Etc.
Hyundai Tiburon Seats (much, much less expensive then Corbeau seats!)
Corbeau Four Point Harness
Stock RB-1 stereo/Cobra CB/I-Pod
800 Watt/120 volt converter in Glove Box with 50 amp circuit breaker at the battery
Jeep Heritage Shifters (K-Bar knife on the transmission, and a Pineapple grenade on the transfer case)
Custom Dog Platform/Bed
An area below the platform to store the soft half door windows
8 Inch Tuffy Box in the rear, complete with 150 piece Craftsmen tool set, winch kit, straps, chains, and extra parts
Military Tools (Pick, Hachette, Trenching Shovel hanging on the inside of the tailgate)
First Aid Kit/HD Flash Lite/Fire Extinguisher.
Quick Release Cargo Tie Down, the rails for this are mounted to the top of the tub behind the front seats
Hi-Lift mounted to Roll Bar
Misc. All Things Jeep Goodies
Nth Tummy Tuck, modified for the Rusty’s Kit
Rokeman Rear Corner Guards
Skid Row Oil Pan Skid Plate
Lower Axle Arm Mount Skid Plates
HD Gas Tank Skid
Steering Box Skid
Skid Row Radiator Skid Plate
ORO Front roll bar system with dash bar
Solid Front and Rear Differential Covers
All J Boulder Bars (2� X 3�) Rock Sliders
Modified ARB Front Bumper with Roll-over grill hoop. Moved about an inch forward to allow room for the Currie Sway Bar.
Factory Rear Light Guards
Quick Removal Pocket Fender Flares, the nuts for the bolts were welded to the body for ease of removal of the flares.
Old Style 35 x 12.50R 15 BFG Mud Terrains on Steel Pro-Comp Wheels
Hella Lighting, headlight, fog lights and driving lights
Hy-Line Hood Vent Panel
Custom Rear Hitch with CJ Stainless Bumperettes
Cold Air Intake Vent takes cold air from the hole left by the right hand side directional signal. Signals are now in the ARB bumper.
9000 Pound Warn Winch (From Dealer)
Custom Vinyl Graphics, now reflective black (makes it go faster)
Roof Rack (used when required)
Tow Buddy, 1967 M416 Trailer (under construction)
Std RB-1
Rusty’s Long Arm Upgrade kit
Currie Upper Front Axle Bushing Kit
Custom Tie Rod Flip, right hand drive drag link, ZJ tie rod, Go-Fer-It bushings, with Rusty’s Sway Bar mount extensions
Track Bar Flip, Frame mount for double shear, axle mount now on top of the axle.
(needed to do that to eliminate the bump steer from the tie rod flip)
Modified Adjustable JKS Front Track Bar, I cut the single shear frame end off, threaded the inside of the bar and installed a Currie Johnny Joint.
Stock JK rear springs on Nth Spring Relocaters (soon to be replaced by ACOS and # inch BDS springs)
Out-boarded the rear shocks
OME 2.5 inch ZJ Springs on JKS ACOS in the front
JKS Adjustable Rear Track Bar w/relocation bracket & mount support
Currie Antirock Front Sway Bar (one of the best modifications to the Jeep)
2 inch front and rear Bump Stops
Lift Height: Approx. 3.5 inches
Wheel and Tire
35 inch BFG


There are no comments to display.